Фомичев Георгий Игоревич
Общие сведения
О себе
Основатель и руководитель компании «Endurance»
Футурист, предприниматель, инноватор.
Спикер на международных конференциях в т.ч. Monage, IEEE, Maker Faire.
Нюансы работы с программой BenBox и лазерным гравером Endurance MakeBlock XY 5.6 Вт
В новой статье наш постоянный автор Георгий Фомичев расскажет о настройках BenBox – программы для работы с лазерным граверами.
Основные параметры программы BenBox следующие:
Настройки Benbox влияют на результативность резки и гравировки.
Параметры и интервалы:
Обратите внимание, в некоторых версиях программы параметр «количество» некорректно отображается.
В целом, программа BenBox удобна тем, что в ней можно работать, как с векторным изображением, так и с растровым. Важно, что также она работает с g-code.
Окно загрузки g-code
Чтобы гравировать изображение с полутонами достаточно загрузить изображение и нажать «play». Но до этого важно разобрать с параметрами гравировки. Если вы хотите гравировать на дереве или фанере рисунок с 8-16 оттенками серого, мы советуем использовать вот такие параметры (указаны для лазера Endurance мощностью 5.6 Вт):
Слабый свет – 50
Интенсивность – 200
Скорость – 1000
Время – 1
Количество – 1
Эти параметры позволят передать полутона и сделать красивое изображение.
Для лазерной резки фанеры на том же станке с лазером 5.6 Вт рекомендуем следующие параметры:
Для лазерной резки черного акрила на гравере Endurance MakeBlock 5.6 Вт установите следующие настройки:
Приведенные параметры являются оптимальными с точки зрения качества и скорость резки. Под качеством мы понимаем чистый рез без обугливаний или оплавлений, под скоростью — приемлемое время для получения результата.
Скачать BenBox и другие программы для подготовки изображений и работы с лазерами Вы можете по ссылке.
Подробнее о работе с лазерами читайте в других статьях от Георгия Фомичева или на сайте компании Endurance.
Источник
Работа программы mDraw и Benbox. Как пользоваться программами для гравировок
Подпишитесь на автора
Подпишитесь на автора, если вам нравятся его публикации. Тогда вы будете получать уведомления о его новых постах.
Отписаться от уведомлений вы всегда сможете в профиле автора.
Здравствуйте дорогие друзья! Лаборатория Endurance представляет краткий обзор программного обеспечения для лазерной резки или гравировки. В этой статье хотелось бы остановиться на двух популярных программах: mDraw и Benbox. Для начала, обратите Ваше внимание, что mDraw кросс-платформенное программное обеспечение с открытым исходным кодом, которое может быть установлено на операционные системы Windows, Mac OS и Linux. Benbox же смогут установить только лишь пользователи Windows.
Нужно отметить основные отличия между данными программами. mDraw проще в освоении, но предназначено только для контурной лазерной резки или гравировки. Benbox же может работать с различными форматами файлов и поддерживает как контурную лазерную резку или гравировку, так и гравировку полутонов. Заметим, что гравировка полутонов позволяет сделать рисунок объемным, но занимает гораздо больше времени, чем контурная лазерная резка или гравировка. Краткие характеристики программ Вы сможете увидеть на схеме.
Обзор программы mDraw
Так выглядит главный интерфейс mDraw
Переместите импортированные графические файлы в прямоугольной области, и проверьте, не выходит ли изображение за рамки рабочей зоны. Проверьте питание лазера, нажмите кнопку[IMG WIDTH=39 HEIGHT=19]file:///C:/Users/User/AppData/Local/Temp/msohtmlclip1/01/clip_image010.jpg[/IMG], чтобы начать гравировку.
Обзор программы Benbox
Характерной особенностью Benbox является поддержка гравировки полутонов и возможность редактировать графики и текста непосредственно в программе.
Так выглядит главный интерфейс Benbox
Помните, что для достижения наилучшего результата Вам нужно провести ряд экспериментов с настройками скорости гравировки.
Демо видео как пользоваться программой Benbox
Демо видео как пользоваться программой CNCC LaserAxe
Команда Endurance всегда рада Вам помочь и поделиться своим опытом. С вопросами и предложениями обращайтесь на e-mail: gf@EnduranceRobots.com или gfomitchev@gmail.com.
Желаем всем удачных гравировок!
Подпишитесь на автора
Подпишитесь на автора, если вам нравятся его публикации. Тогда вы будете получать уведомления о его новых постах.
Отписаться от уведомлений вы всегда сможете в профиле автора.
Источник
BenBox software
Inside of the file you will find the BenBox software, the driver for the CH340 chip of the microcontroller, the hexadecimal code to be uploaded to the microcontroller and an example file to print (logo).
Installing the software
Download the zip file below and extract it. Inside you have the software but also the firmware for the main board in a hexadecimal format. First make sure you install the CH 340 driver. Once that is done, install the benbox software and open it. Here click the update firmware in order to upload it to the board. Select the Com of the machine board and open the hexadecimal file that you have in the downloaded folder. Upload and wait till you get a green check mark.
Now go to serial ports. If it says success than you are ready to go. In the parameters you must place this same values as you can see in the photo above for X and Y movement as for the laser as well. Save and now let’s make a test.
I’ve designed the file in Photoshop and save it in a BMP format. Click open and select that file (logo). Now make sure you have the safety glasses on, and that you’ve focused the laser. Press the laser push button to put it into weak mode and rotate the laser tip till you get a very small and well focused beam. Remember to disactivate the weak mode and we are now ready to print.
Change your settings in the print config if you want and click play and the machine will start engraving. Make sure you open a window or have fume extractor since this will create a lot of smoke especially when you are engraving wood.
There you go, I’ve burned my first logo on a piece of wood. You could play with the machine settings and try other materials.
Results
Now my final opinion on this machine, well, it dose everything I expect it to do before buying it. The printing size is quite big of around 46 by 38 centimeters. It has decent precision that could even get better with more calibrations. It is very fast and easy to mount in just a couple of hours and also very easy to use. It has a great design, it looks nice and it’s quite powerfull. And that’s the problem. This machine has very few safety features. First of all it doesn’t have a case so you won’t be protected from laser exposure. The glasses they give you aren’t that good and for a direct beam exposure they might not protect you. Another issue I’ve seen is that when the machine is powered and you connect the USB the laser will be at of full power and if you’re not careful, that might hurt you. There is clearly an error where the boar enables the laser when the USB is connected and that second is enough to hurt you. So make sure you have the weak mode selected before starting the machine.
A good thing about this machine is that in any moment you could remove the laser module and add a drill and use it as a soft milling machine. Maybe I’ll try that in the future. As for the components quality, well, the frame is made out of metal and that’s a good thing. The kit was missing some metal corners for the main frame, but any way the frame seams quite strong only with the acrylic joints. It ahs V shaped rollers, powerful enough step motor and the main board, well, is one of the cheapest there is. It’s based on Arduino and with two step motors drivers and that’s it. The drivers have no heat sink on top of them so I’ll probably add those myself. Also, the USB cable is quite short, a longer one would definitely be better.
Anyway, I like it, I’ll have to use it for a longer period of time in order to see more good or bad things about it but for now I can say that this machine is ok as for quality and price. You have the link for this machine below from banggood for around 180 euros which I guess is a fair price since only the laser module is like 100 euros. You have the 2.5W model or the more expensive one of 5W laser module. You decide which one you’ll buy. With one like mine of 2.5W you would be able to burn wood, plastic, leather and much more. I hope that you’ve enjoyed this small intro on this EleksMaker CNC laser engraver.
If you would like to help my projects, I have a Patreon campaign. I would really appreciate that guys.
I hope that you’ve enjoyed this review. If so don’t forget share the project with your friends. If you have any question about this review or any other, just leave it on my Q&A page. Also, don’t forget to subscribe and watch all of my other great tutorials. Remember, if you consider helping my projects check my Patreon page as well. Thanks again and see you later guys.
Источник